Téma: LineageOS 14.1 (7.1.2) Ace 3 LTE

[gyu456]

SAMSUNG GALAXY ACE 3 LTE
(GT-S7275R)

Nougat 7.1.2

Ha gyári a recovery-d, akkor előbb You are not allowed to view links. Register or Login felrakod CWM-t vagy a TWRP-t, majd:

Telepítés:
1. Mounts and storage --> Format system
2. Mounts and storage --> Format data
3. Wipe data & factory reset
4. Wipe cache
5. Wipe dalvik cache
6. Install ROM
7. Reboot
8. Install GAPPS
9. Reboot

You are not allowed to view links. Register or Login or You are not allowed to view links. Register or Login

-20171021-

You are not allowed to view links. Register or Login or You are not allowed to view links. Register or Login

Hibák:

-Enabling alarms triggers random reboots
-NFC, as usual, no source is available
-Camcorder
-Broken livedisplay, disabled by default, DON'T try to enable it.
-SELinux permissive
-Some settings do not apply
-Maybe some more not discovered yet




You are not allowed to view links. Register or Login

Figyelem! Semmilyen felelősséget nem vállalok, ha valamilyen oknál fogva a telefont károsodás éri! A felelősség Téged terhel, csak akkor kezdj neki, ha biztos vagy benne mit csinálsz! Ne felejts el biztonsági másolatot készíteni az összes fontos fájlról! Fontos!

Ha valamit nem értesz, most hallasz róla először, NE ÁLLJ NEKI!!!

[gyu456]

Aki netán majd fel rakja, jöhetnek a képek és tapasztaltok

[gyu456]

-20160929-

*CM sources update
*audio: Update mixers
*audio: Enable voice path for PCM voip
*Kernel: BACKPORT: ASoC: msm: Add support to change bit rate during VoIP call
*Kernel: BACKPORT: ASoC: msm: qdsp6v2: Add support for non-pcm VoIP formats
*Kernel: BACKPORT: ASoC: msm: qdsp6v2: Add support to configure min and max rates

-20160924-

*Initial release

[gyu456]

-20161010-

*CM sources update
*Fixed Screen Recording
*Switch back to AOSP browser
*Kernel: BACKPORT: mm: /proc/pid/smaps:: show proportional swap share of the mapping
*Kernel: ptrace: fix ptrace defect cause by a merge fail
*vendor: Updated Adreno blobs from Nexus 7 (MOB30M)
*vendor: Update libRSDriver_adreno blobs
*vendor: Remove libOpenCL blob
*vendor: Remove qcom audio codecs

[bubi90]

Szia!

Öcsémnek nemrég lett egy Ace 3 telója gyári rommal, garancia már nincs rá. Az a baja, hogy hiába nincs rajta bekapcsolva sem a wifi, mobilnet, gps, stb, mégis egy éjszaka alatt merül az aksi 80%-ot. Én szerintem ez azóta van, hogy beletettük a telekomos sim kártyát. Volt már gyári visszaállítás is többször is, de ugyanaz a hiba.

Létezik erre valamilyen gyógymód vagy a CM rom megoldja? Öcsém nem túl jó angolos, van benne magyar nyelv?
Egyébként nincs már baj a gyári rommal, használat közben is csak lassan fogy az akksi. De mikor letesszük egy időre, akkor durván le tud csökkenni.

Köszi előre is!! (és bocsi az ismétlésért)

[gyu456]

-20161028-

*CM sources update
*Fix camcorder

[gyu456]

-20161103-

*CM sources update
*Android 7.1

[gyu456]

-20161123-

*CM sources update
*Android 7.1.0_r7
*rootdir: Modify LMK parameters
*Revert "common: Enable kernel exFAT"
*Remove legacy MMAP
*rootdir: Re-enable selinux enforced
*fstab: Assign unused pad partition to /misc
*overlay: Set default country index in FM app to Europe
*Enable delay service restart
*libshims: Fix libshim_wvm
*Add shim for libwvm.so
*Rename shim libs
*Specify cache file system type
*msm8930-common: sepolicy: Updates for N
*msm8930-common: sepolicy: Add back device specific rules
*msm8930-common: Modify flags for camera support
*msm8930-common: overlay: Disable IpReachability monitor
*msm8930-common: Use multithread decode for boot animation
*Kernel: ARM: dts: msm: Add support for UIO devices for RemoteFS
*Kernel: uio: msm_shared: Add support for platform data
*Kernel: uio: msm_sharedmem: Add new device driver for sharedmemory access
*Kernel: uio: provide vm access to UIO_MEM_PHYS maps
*Kernel: Revert "drivers/uio: sync with serrano source"
*Kernel: Fixing bad conflict resolution
*Kernel: seq_file: always update file->f_pos in seq_lseek()
*Kernel: msm_iommu: Add missing code from flo kgsl merge
*Kernel: Effectively revert "gpu: ion: replace __GFP_ZERO with manual zero'ing"
*Kernel: Bluetooth: ath3k: Use GFP_KERNEL instead of GFP_ATOMIC
*Kernel: Bluetooth: ath3k: output firmware filename when request_firmware failed
*Kernel: Bluetooth: btusb: fix bInterval for high/super speed isochronous endpoints
*Kernel: btusb: fix a memory leak in btusb_send_frame()
*Kernel: Bluetooth: btusb: Free driver data on USB shutdown
*Kernel: USB: convert drivers/bluetooth/* to use module_usb_driver()
*Kernel: ASoC: msm: Return signed error code
*Kernel: msm: mdp: wait for previous frame commit before unset

[gyu456]

-20161207-
*CM sources update
*Android 7.1.1_r4
*Use prebuilt CMFileManager from CM13
*cleanup ril
*msm8930-common: selinux: Label misc block device
*qcom-common: doze: Commonize strings translations
*qcom-common: Automatic translation import
*vendor: updates from I9195XXUCPE1
*vendor: Updates from E370KKTU2BPH2
*vendor: Remove unused Adreno blobs
*vendor: Revert "Updated Adreno blobs from Nexus 7 (MOB30M)"
*vendor: Remove unused blobs

[gyu456]

-20170109-

*LineageOS sources update
*mpdecision: let 2nd core to sleep
*Remove dock settings
*Revert "Use prebuilt CMFileManager from CM13"
*msm8930-common: sepolicy: Fix denials after restore of ROM backup


-20161221-

*CM sources update
*Android 7.1.1_r6
*ril: Override non-standard data network types.
*overlay: Misc cleanup
*overlay: Disable bluetooth by default
*msm8930-common: sepolicy: Unbreak bluetooth
*qcom-common: doze: Clean up ambient display pref dependencies
*Kernel: defconfig: Enable RPFILTER

[gyu456]

-20170121-

*LineageOS sources update
*Set BOARD_HAVE_QCOM_FM
*Remove config_extraFreeKbytesAdjust from overlay
*Kernel: mipi_magna_oled.c: fix logic
*Kernel: mipi_NT35510.c: fix logic
*Kernel: fs:fuse: Disable shortcircuit when mmap is called on a file
*msm8930-common: Revert "Include extended font selection"
*qcom-common: doze: specify a qualified user to send the pulse broadcast
*qcom-common: qcom: doze: Protect com.android.systemui.doze.pulse
*qcom-common: Revert "Revert "doze: Add back button to action bar""

-20170115-

*LineageOS sources update
*Optimize low memory killer
*Increase zRam size
*Memory tweaks
*msm8930-common: sepolicy: Allow init to write in debugfs
*msm8930-common: camera: Remove HDR scene mode
*msm8930-common: sepolicy: Fix mediaserver denial for gemini device
*qcom-common: doze: Move to display settings

[gyu456]

-20170208-

*LineageOS sources update
*overlay: Disable the recovery update function
*Bring back Gello, stock browser has bugs and no one is planning to fix them
*Add support for TWRP
*Fix copying of init.recovery.qcom.rc
*Set mobile data to off by default
*msm8930-common: sepolicy: Cleanup
*Kernel: net/unix: sk_socket can disappear when state is unlocked
*Kernel: Set the iif for IPv6 packets as well.
*Kernel: defconfig: Disable kernel exFAT
*Kernel: net: Loopback ifindex is constant now
*Kernel: netfilter: xt_rpfilter: skip locally generated broadcast/multicast, too
*Kernel: ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif

-20170126-

*LineageOS sources update
*msm8930-common: camera: Extend supported scene modes
*qcom-common: doze: Remove extraneous meta-data
*Kernel: Huge update from 3.4.0 to 3.4.113

[gyu456]

-20170701-

*Android-7.1.2_r8 -> Android-7.1.2_r17
*Run clang-format on source files
*prop: Set a couple bluetooth props
*rootdir: Clean bluetooth script for unused stuff
*prop: Set bluetooth HFP version to 1.6
*libligths: Specify device api version
*overlay: Define custom RAT family
*prop: Remove obsolete ro.sys.fw.dex2oat_thread_count prop
*bluetooth: Remove KERNEL_MISSING_CLOCK_BOOTTIME_ALARM define
*init.qcom.rc: Set freeze timeout to 2 seconds
*camera: Cleanup ISO parameters
*msm8930-common: Consolidate some camera flags
*msm8930-common: Remove obsolete and unused flags
*msm8930-common: Run clang-format on source files
*msm8930-common: sepolicy: Don't set labels we don't need to
*msm8930-common: sepolicy: Label battery status nodes
*msm8930-common: Remove NUM_FRAMEBUFFER_SURFACE_BUFFERS define
*Kernel: Wlan: Optimize set key part to reduce the set key time
*Kernel: wlan: Fix null mac address check in WDA
*Kernel: wlan: Return updated rssi value to upperlayer
*Kernel: wlan: Update qie_age->age to match the BSS age in the driver
*Kernel: wlan: Increase the Wait for key timer value
*Kernel: wlan: Disconnect the session when WaitForKey timer expires
*Kernel: wlan: Use system time instead of jiffies for BSS received time
*Kernel: prima: Reduce expiration time of traffic timer during roaming
*Kernel: drivers/staging: Configurable android log buffer sizes
*Kernel: drivers/staging: msm8610: Reduce android log buffer sizes
*Kernel: staging: android: logger: Correct write offset reset on error
*Kernel: staging: android: logger: enforce GID and CAP check on log flush
*Kernel: staging: android: logger: Allow a UID to read it's own log entries
*Kernel: staging: android: logger.h: Complete documentation of logger_entry
*Kernel: Staging: Android: logger: module_exit implementation
*Kernel: staging: android: logger: Finish documentation of two structs
*Kernel: staging: Android: Fix some checkpatch warnings
*Kernel: staging: android: logger: Fix some sparse and whitespace issues
*Kernel: staging: android: logger: Allocate logs dynamically at boot (v3)
*Kernel: staging/android: use module_platform_driver
*Kernel: staging: android: timed_output : disable the timed output device when the device is unregistered
*Kernel: defconfig: Enable Android alarm driver
*Kernel: max17050_fuelgauge: Migrate to alarmtimer interface
*Kernel: sec_battery_8930: Migrate to alarmtimer interface
*Kernel: pm8921-sec-charger-8930: Migrate to alarmtimer interface
*Kernel: SELinux: include definition of new capabilities
*Kernel: UPSTREAM: timerfd: Protect the might cancel mechanism proper
*Kernel: timerfd: support CLOCK_BOOTTIME clock
*Kernel: timerfd: add alarm timers
*Kernel: switch timerfd_[sg]ettime(2) to fget_light()
*Kernel: rtc: pm8xxx: move device_init_wakeup() before rtc_register
*Kernel: rtc: pm8xxx: Sync up to upstream version
*Kernel: alarmtimer: add rtc irq support for alarm
*Kernel: alarmtimer: add alarm_expires_remaining
*Kernel: alarmtimer: add alarm_start_relative
*Kernel: alarmtimer: add alarm_forward_now
*Kernel: alarmtimer: add alarm_restart
*Kernel: alarmtimer: Rename alarmtimer_remove to alarmtimer_dequeue
*Kernel: alarmtimer: implement minimum alarm interval for allowing suspend
*Kernel: staging: alarm-dev: information leak in alarm_ioctl()
*Kernel: staging: alarm-dev: Implement compat_ioctl support
*Kernel: staging: alarm-dev: Refactor alarm-dev ioctl code in prep for compat_ioctl
*Kernel: staging: alarm-dev: Drop pre Android 1.0 _OLD ioctls
*Kernel: Staging: android: Alarm driver cleanups
*Kernel: staging: android: alarm: remove unnecessary goto statement
*Kernel: staging: Android: Fix NULL pointer related warning in alarm-dev.c file
*Kernel: Staging: android: alarm: Rename pr_alarm to alarm_dbg
*Kernel: staging: android-alarm: Switch from wakelocks to wakeup sources
*Kernel: Revert "rtc: Add android alarm driver."
*Kernel: Revert "rtc: alarm: Add in-kernel alarm interface"
*Kernel: Revert "HACK: time: Disable alarmtimer"
*Kernel: PM / Runtime: Improve prepare handling at system suspend for genpd
*Kernel: PM / Runtime: Asyncronous idle|suspend devices at system resume
*Kernel: PM / Domains: don't use [delayed_]work_pending()
*Kernel: PM: Move disabling/enabling runtime PM to late suspend/early resume
*Kernel: PM: Reorganize device PM initialization
*Kernel: PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
*Kernel: PM / wakeup: Use irqsave/irqrestore for events_lock
*Kernel: PM / QoS: Add return code to pm_qos_get_value function.
*Kernel: suspend: enable freeze timeout configuration through sys
*Kernel: PM: Introduce suspend state PM_SUSPEND_FREEZE
*Kernel: power: Squashed revert of CAF's suspend_sys_sync feature
*Kernel: msm: Disable ultrasound driver
*Kernel: pm8921-sec-charger-8930: Let's override the charging mode only for LPM
*Kernel: sec-battery: Let's override the charging mode only for LPM
*Kernel: sec-battery: Standardize the output of the "online" property
*Kernel: msm: pm-8x60: Increase warn timeout for sleep sts check
*Kernel: PM: Rename CAP_EPOLLWAKEUP to CAP_BLOCK_SUSPEND
*Kernel: epoll: Fix user space breakage related to EPOLLWAKEUP
*Kernel: epoll: Add a flag, EPOLLWAKEUP, to prevent suspend while epoll events are ready

-20170520-

*LineageOS sources update
*Android 7.1.2_r8
*overlay: Disable dreams by default
*Switch to MDP composition
*overlay: Don't allow installing non market apps by default
*overlay: Enable lock screen rotation setting
*Remove Gello from the build
*Revert "overlay: Disable the recovery update function"
*overlay: Disable auto brightness toggle in QS panel
*init.qcom.usb.rc: Additional cleanups
*Add shim for libc to fix camera crash
*Add Prima firmware and configuration
*bluetooth: Enable vendor specific BLE code
*Nuke widevine and qseecom blobs
*Remove persist.sys.usb.config
*Add single adb mode and clean out not used modes
*Remove CellBroadcastReceiver overlay
*Move USE_CUSTOM_AUDIO_POLICY flag to msm8930-common
*Move LZMA_RAMDISK_TARGETS out of twrp.mk
*fstab: Assign fota as the misc partition
*twrp.fstab: rearrange line order
*Remove preload from twrp.fstab
*overlay: Remove date and time page from setup wizard
*keylayout: Cleanup files
*overlay: Hide sRGB toggle in developer options
*Use AOSP POWER_HINT_BOOST
*Fix typo derp in twrp.fstab that broke encryption
*overlay: Match keyguard status bar height with regular status bar height
*msm8930-common: overlay: Disable SIM batch operations
*msm8930-common: Decommonize prima wlan firmware
*msm8930-common: Rename hide wifi region code bool
*msm8930-common: Remove custom GLES shader cache sizes
*msm8930-common: Move TARGET_PROVIDES_LIBLIGHT to devices
*msm8930-common: Fix firmware denial
*msm8930-common: Add sshdcpap firmware symlink
*msm8930-common: Add USE_CUSTOM_AUDIO_POLICY flag
*msm8930-common: sepolicy: Resolve a few new denials
*msm8930-common: Nuke config_wifi_ipreachability_monitor overlay
*msm8930-common: prima: Disable 802.11d support
*msm8930-common: sepolicy: Minor cleanup
*qcom-common: Remove animate screen lights
*qcom-common: remove deprecated eri overlays
*Kernel: msm: remove fmem support
*Kernel: gpu: ion: Remove code for reusable heap
*Kernel: misc: Remove pmem driver completely
*Kernel: msm: Remove ANDROID_PMEM from the Kconfig dependencies
*Kernel: msm: Remove all references to pmem from audio files
*Kernel: msm: camera: Remove references to CONFIG_ANDROID_PMEM
*Kernel: msm: wfd: Remove reference to android_pmem.h
*Kernel: crypto: msm: Remove use of PMEM
*Kernel: msm: Remove all references to CONFIG_ANDROID_PMEM
*Kernel: msm: vidc: Remove all references to CONFIG_ANDROID_PMEM
*Kernel: ASoC: msm: Remove android_pmem.h header
*Kernel: msm: remove references to CONFIG_ANDROID_PMEM
*Kernel: ASoC: msm: Adjust buffer bytes and num periods for proxy driver
*Kernel: wireless: sort and extend element ID list
*Kernel: wlan: Remove WLAN_FEATURE_HOLD_RX_WAKELOCK feature
*Kernel: msm: 8960: Add A2_BAM_IRQ to bypass irq list
*Kernel: msm: mpm: Print interrupts which are not monitorable.
*Kernel: kernel: Only expose su when daemon is running
*Kernel: fs: take i_mutex during prepare_binprm for set[ug]id executables
*Kernel: input: evdev: Move wake_lock_destroy call
*Kernel: mmc: core: Fix possbile memory leak
*Kernel: msm: watchdog: Fix Watch Dog timeout(reset) issue
*Kernel: battery: max77693: Be more AOSP-friendly
*vendor: Nuke most widevine related blobs
*vendor: Kang latest time_daemon blobs from Shamu